Replacing Your Clutch Jet on Your Aprilia Gen 1 & 2 RSV, RSVR & Tuono

Comments · 54

• FL

  @flyjayUK · 3 years ago

  &quot;You may lose a touch of oil, it&apos;s not going to pour out&quot; . . . . &nbsp;. Yea, I had a nice puddle of oil on the floor :D<br><br>Not been out for a ride since I&apos;ve just fitted it, but in the garage, it went up and down the gears and back into neutral perfectly. &nbsp; Can&apos;t believe something so tiny can make a difference like that.

  8

• RO

  @RosscoSharp · 3 years ago (edited)

  Nice one Griff, once again saving the day. Mine was dragging so badly neutral impossible and on the paddock stand only hard rear brake would stop the wheel spinning with the lever in. <br>Of course fully bled with better fluid, lever adjusted etc. No difference. The #40 jet fixed it. Nicer shifting, neutral easy (up or down) and no dragging. Who&apos;d have thunk a poxy jet was causing all the issues. <br>AP Workshops 👌THANK YOU

  4

• PH

  @phillharrys505 · 3 years ago

  No way... seriously all those years of crappy neutrals is this easily fixed.... online order coming your way tonight for 2x units.. cheers guys

  4

• MO

  @moozepatt7525 · 1 year ago

  just pulled mine while doing an oil change to make sure it would come out. The toothpick didn’t work but I cleaned the hole with alcohol on cotton swabs then stuck a big (150cc) syringe in and pulled the plunger while pulling back the syringe and it popped right out. love your videos

  2

• MO

  @motorcyclemicah6309 · 5 years ago

  Oh look... &nbsp;An AP Workshops video! &nbsp;&lt;*Immediately* hits &quot;like&quot; button&gt; then watches. &nbsp;Thanks Griff and team for putting these videos together. &nbsp;They&apos;re most helpful for those of us across the pond who must work on their own Aprilias.

  3

• MP

  @MPjustaman · 5 years ago (edited)

  Seems my screwdriver went in a bit further and I&apos;m having the dickens of a time getting my old jet out.<br>Got it! Much better now! Used a bamboo skewer and gave it a good tap then it seated in the old jet. The problem was the old jet was bumping on the sides of the hole and coming off my &quot;cocktail&quot; stick.<br>Took the bamboo skewer and ran it through a pencil sharpener to give it a bit more of a tip not too much mind you, I did not want it snapping off in the old jet. <br>The bamboo is a bit sturdier than the cocktail stick which also assisted in securing a good seating in the old jet. <br>Thanks Griff for the part and video post it helped a lot.

  1

• ST

  @stephenmcqueen4029 · 5 years ago

  To prevent stripping the thread on reinstalling you should really turn it backwards until it clicks over the thread and then you know you can screw in without crossing the thread up.

  8

• RE

  @redbeard3923 · 4 years ago

  Great man always got time to email back when you ask a technical question 👍

• AN

  @andreasmeier6605 · 1 year ago

  Thats cool! Thanks!

• JA

  @Jay-Italian-steeds · 6 years ago

  Nice one griff I have this problem, soon to be rectified thanks 👍

  1

• CH

  @charlesbenjamin3089 · 6 years ago

  Griff, been a while but showing Love from Japan and saying keep up the good work with you and your team. &nbsp;Just got done watching “chasing tenths” newest video and have a request for us wrench turners.<br>Request that you and your team please go over suspension set up front and back for RSV4, since there are difference between suspension components since my 11’ to 20’. &nbsp;General considerations what setup should be with and without weight and wear issues you have seen and what owners are missing. &nbsp;Thank You Again.

  1

• XY

  @xyz-md8ov · 5 years ago

  brilliant, thanks a lot